Fancontrol software9/22/2023 ![]() This feature is only available on 20 models. Accepted values are 2-7, where 2 is the fastest and 7 is the slowest. Values represent a few seconds each, where 0 is the fastest and 9 is the slowest.ĭetermines how quickly the fans accelerate or decelerate when it is time to change fan speeds. Only available in Discrete Graphics Mode (Hybrid Off).ĭetermines how often LegionFanControl should check the current temperature before deciding to change fan speed or not. Removes laptop control of the fans so they run at their factory maximum speeds. Some users may want to disable this behaviour if they use other tools to manage their Windows Power Plan switching events You can control CPU fan speed with software or your PC's BIOS. Will also switch corresponding Windows Power Plans if they existĬhoose whether switching the Legion Power Mode will also switch the corresponding Windows Power Plans if it exists. Updated on MaReviewed by Michael Barton Heine Jr What to Know Windows 11 doesn't offer a built-in tool for monitoring or controlling CPU fan speed. Stock Fan Curve settings are restored on exiting the application. ![]() The maximum allowed Fan Speed in the curve is dynamically determined based on Lenovo recommendations for your model.Decide what the fan speeds should be at each temperature point.Decide the temperature points when the fan speeds will change.Create a custom fan curve for each Power Mode. ![]() If the problem would be here, it would show up also without using other tools and much sooner. Moreover, HWiNFO is used by a lot more users than FanControl and none of them reported a similar issue running it alone. Overview FAQ Certified What's New Similar to 3 FanControl lets you combine any type of fan curves together and apply. Sorry for not providing a deeper insight, but I don't feel responsible for this issue, hence cannot afford spending more time on a deeper analysis of FanControl or LHM. Software fan control is a feature that allows you to adjust the speed and behavior of your CPU and case fans, depending on the temperature and load of your. Fan Control is a highly customizable fan controlling software for Windows. So, I believe the problem is not in HWiNFO, but just some coincidence revealing a problem in LHM or FanControl. This could be one problem.Īnother interesting piece is the RestoreDefaultFanControl method which might be the culprit to what you observe after closing FanControl. This is something HWiNFO doesn't do and it keeps the original configuration as set by the system BIOS. I checked the LHM code and (besides finding some areas not not protected by the mutex) I also see that it performs some sort of initialization of the eSIO hardware monitor by enabling additional voltage monitors. ![]() Your comment about appearing of new garbled sensors in HWiNFO when starting it after FanControl might point to some issue in LHM. As such, please be patient and as descriptive as possible if you want any chance of this getting resolved. Please note that all of them provide voluntary support for software you can use for free, and the issue you're having is most likely very difficult to debug / determine its origin unless it was clearly reproducible by everyone (which it sadly is not). HWInfo64 would then also start displaying a lot of new sensors on my NCT6687D which were garbled/incorrect (have readings of 0).Īlso to address PP2012/resudroid: I have noticed that you seem to be a bit pushy in terms of communication with developers of both FanControl and HWI. When HWInfo64 was started after FanControl, it would cause issues with FanControl's ability to, well, control fans. When I had the issue, yes, the start order of FanControl and HWInfo64 did matter in my case. So from my perspective the issue is not clear-cut. Change the settings as desired, then save and exit. The problem PP2012 describes is something that I was able to observe on my system as well (but was fixed for me by updating both HWInfo64 and FanControl, or by magic I don't understand). Fan speed will typically be shown as a value between 100 and 0, where a value of 100 is the fan's highest setting, while a value of 0 is the lowest. I have observed LHM clashing with other hardware monitoring tools in the past intermittently, but I never observed HWInfo clashing with others. To clarify: I'm not affiliated with FanControl but am following the issue thread on github. ![]() First of all: Thanks Martin for responding and even showing interest in this issue at all, because it is quite obscure and only shows up for a small portion of users. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |